Keyword Search: 
Part No. Search: 
OO Scale N Scale G Scale Z Scale HO Scale Slot Cars & R⁄C
  ON THIS SITE  
  SHOPPING BASKET  

Your shopping basket is empty.  To add an item, click the "Buy" button

  YOUR ACCOUNT  
  GAUGEMASTER  
prodigy advance
Gaugemaster Controllers
O Scale Wargaming Architectural Narrow Gauge Tools+
Right Lines e-Zine

Expanding Your O Scale Layout

Part 4

Terry Smith

TERRY SMITH looks at basic scenery and shows how even a flat coal yard can benefit from some undulations.

Hoping that I was going to start ballasting, I sprayed Humbrol AXD6029 Dark Earth close to the laid track sleepers so at least the ballast when applied would already have some earth colour underneath it next to the line.

I also gave the coal yard area a dusting of Humbrol AXD6033 Matt Black spray then it hit me how flat everything looked. I had contemplated on using 1/8th cork under the track but decided as this was a yard it wouldn't look right. In the actual yard itself the rails are pretty much level with any kind of road surface, but in the approach to the yard I decided to give the track a bit of a lift.

O Scale Layout Building

Initially I sprayed dark brown paint close to the track and then decided to chisel away the base board next to it.

The board used was 18mm MDF which was finished with a plastic wood effect, thick enough to carve into in places but still leave enough thickness for it to keep its integral strength. A quick trip down to a local DIY store and I returned with two nice new chisels at around 1/4" and 1" wide. Using the narrower of the two , I gouged out what at first looked like a drainage ditch. Once I started to use the wider one I just kept cutting into the board at around a 45 degree angle.

O Scale Layout Building

Once you start using the bigger chisel the ground really starts to drop away.

O Scale Layout Building

With the track lifted you can go to town, this is as far as I felt I needed but I am sure I could have gone deeper if I required.

I didnít need to use a hammer, the new chisels were sharp enough to use with just the pressure from my hand. After looking at my initial handywork, I decided to cut into the baseboard in other places as well. I used a felt pen to draw out where features such as the roadway inside the yard was going to go and where I could also put dips in the surface to create ground variation.

O Scale Layout Building

The chisel technique also lends itself to other areas of the layout, this is the curb near the yard's entrance. The roadway areas also benefit from having a curved shoulder cut into the top of the board.

At this point I decided as (a) this was going to get messy and (b) I didnít want to damage the track with an errant chisel, so I lifted all but the first piece of the Peco SETRACK. If you remember, I used DLAD-45 Roket Max adhesive to stick occasional sleepers to the board - with only the first piece being stuck firmly. A blade under the other glued sleepers was enough to break the bond. Now with the board almost clear of track I could really start to go to work, chiselling away to my heart's content.

O Scale Layout Building

A quick look at where I had already cut away, made me realise that there was a lot more that could be done on this board to create undulations.

Once all of this had been done and the considerable mess cleared up, I then thought about how I could raise any parts of the layout, and for this I used my new best friend the Gaugemaster Balsa Bundle. By cutting out land mass shapes from the 1/4th thick wood, smaller 1/8th sections could then be stuck on top and sanded to create a natural contour, with a minimum coat of filler over the top.

O Scale Layout Building

This piece of 1/4" balsa was cut to fit the area next to path. Once stuck in place it was given a light coating of filler and sanded to a natural contour.

I always planned to have the ground rise up in the right rear corner of the tunnel end, but now my board has taken on some extra undulations to create a more realistic setting for the track.

O Scale Layout Building

This shallow bank was made from 1/4" balsa with a 1/8th stuck on top and then sanded. Filler will be used to seamlessly blend this into the slope of the gully next to it.

O Scale Layout Building

This is the view looking towards the yards exit. The camber of the road has been carved with the chisels, all it needs now is a tarmac coloured paint finish Ė note the pot holes, more on these next time.

O Scale Layout Building

Compared to the image above after the first cut, now the whole layout has had the chisel treatment. The white areas are mainly where filler has been applied over balsa mounds.

Maybe in the next instalment I will get some track ballasted!

  POPULAR BRANDS  
Gaugemaster
Fordhampton Kits
Hornby
Bachmann
Graham Farish
Atlas
myWorld
Walthers
Kato
Fleischmann
Noch
Preiser
Piko
Peco
Roco
Oxford Diecast
Dapol
Viessmann
Faller
Marklin
LGB
Trix
Deluxe Materials
Revell Paints
Humbrol Paints
Train Tech
DCC Concepts
Seuthe
Facebook Instagram Twitter

We are always looking to make improvements to our website to try and improve the quality of your visit.  We would welcome your feedback and suggestions, so please do not hesitate to e-mail our webmaster with your comments.  Alternatively call us on 01903 884488.

Home  Cookies  Privacy Statement  Terms & Conditions  Site Map  Site Guide
WEEE Regulations  Glossary  Careers & Jobs

Tel –  +44 (0) 1903 884488  Fax –  +44 (0) 1903 884377  E-Mail us –  click here

Gaugemaster.com is a trading name of Gaugemaster Controls Ltd.
Registered in England No. 2714470, Registered office:
Gaugemaster House, Ford Road
Arundel, West Sussex, BN18 0BN, United Kingdom

VAT Reg. No. 587 8089 71

Copyright © 2003-2014 Gaugemaster Controls Ltd. All Rights Reserved.